When ethernet not working on PC is the problem, the cause is usually one of four things: a loose or damaged cable, a disabled network adapter, a corrupted driver, or a router that hasn't handed out an IP address. Check the cable and port lights first, restart the router, then run the Windows network troubleshooter, reset the network stack with a few commands and reinstall the Ethernet driver. Network reset is the last resort.
Why Is Ethernet Not Working on My PC?
Ethernet stops working on a PC when something breaks the chain between the router, the cable, the network adapter and Windows. Working out which link failed saves time, and Windows usually gives you a clue.
| What you see | Likely cause | Where to start |
|---|---|---|
| "Network cable unplugged" or no lights on the port | Cable, port or router fault | Reseat or swap the cable; try another router port |
| Ethernet missing from Settings entirely | Adapter disabled, driver missing or LAN disabled in BIOS | Advanced network settings, then Device Manager |
| "Unidentified network" or "No internet" | No IP address from the router (DHCP failure) | Restart router, then renew the IP address |
| Connected, but websites won't load | DNS or proxy problem | Flush DNS; check proxy and VPN settings |
| Stopped after a Windows update | Driver replaced or update conflict | Roll back the driver or remove the update |
The "Unidentified network" case is worth understanding. When the router doesn't answer the PC's request for an address, Windows assigns itself one starting with 169.254. That address can't reach the internet, so the connection looks active but nothing loads. Fix the router or renew the address and the problem disappears.
How Do You Check the Cable, Port and Router?
Check the physical connection first, because it causes a large share of Ethernet problems and takes two minutes to rule out.
- Look at the Ethernet port on the PC. Most have a small light that glows or flickers when a working cable is connected. No light usually means a cable, port or router problem.
- Unplug the cable from both ends and push it back in until it clicks.
- Make sure the router end is in a LAN port, not the port that connects to your modem or internet line.
- Try a different cable and a different port on the router.
- Restart the network equipment: unplug the router and modem, wait about 30 seconds, plug the modem back in first, wait for its lights to settle, then power on the router.
If another device works on the same cable and port, the problem is on the PC. If nothing works, contact your internet provider.
How Do You Fix Ethernet Not Working in Windows 11?
To fix Ethernet in Windows 11, work through these steps in order and test the connection after each one. Microsoft's Fix Ethernet connection problems in Windows guide follows the same sequence.
1. Check the adapter is enabled
- Open Settings → Network & internet and look for Ethernet. It should say Connected.
- If it is missing, go to Settings → Network & internet → Advanced network settings.
- Find your Ethernet adapter under Network adapters and select Enable if it is disabled.
2. Run the network troubleshooter
Open the Get Help app and run the Network and Internet troubleshooter, or go to Settings → System → Troubleshoot → Other troubleshooters and run Network and Internet. It detects disabled adapters and IP problems automatically.
3. Reset the network stack with commands
- Select Start, type Command Prompt, then choose Run as administrator.
- Run these commands one at a time, pressing Enter after each:
netsh winsock resetnetsh int ip resetipconfig /releaseipconfig /renewipconfig /flushdns - Restart the PC.
If pages still load slowly once you are connected, our guide to fixing slow DNS lookups on Windows covers the name-resolution side in more depth.
4. Reinstall the Ethernet driver
- On another device, download the latest LAN driver for your PC or motherboard from the manufacturer's website and copy it to a USB stick, in case Windows doesn't reinstall it automatically.
- Right-click Start and open Device Manager.
- Expand Network adapters, right-click your Ethernet adapter (often named Realtek, Intel or Killer) and select Uninstall device.
- Tick Attempt to remove the driver for this device, select Uninstall and restart.
- Windows should reinstall the driver on startup. If it doesn't, install the driver from your USB stick.
If Ethernet broke straight after an update, right-click the adapter, choose Properties → Driver → Roll Back Driver, or see our guide on how to uninstall a Windows update.
What If Ethernet Doesn't Appear at All?
If Ethernet doesn't appear in Settings or Device Manager, Windows can't see the adapter, which points to firmware, driver or hardware rather than settings.
- Onboard LAN disabled in BIOS. Some desktop motherboards let you switch off the built-in network controller. Enter the BIOS using our guide on how to access BIOS in Windows 11 and check that the onboard LAN controller is enabled.
- Fast Startup. Windows' Fast Startup feature saves part of the system state when you shut down, and occasionally the network adapter fails to initialise afterwards. A full restart (not shut down) rules this out; our guide to disabling Fast Startup explains how to turn it off permanently.
- Hidden or unknown devices. In Device Manager, select View → Show hidden devices and look for an "Ethernet Controller" with a warning icon under Other devices. That means the driver is missing.
- Failed hardware. If the adapter never appears, even after a BIOS check, the port may have failed. A USB-to-Ethernet adapter is a cheap way to confirm this and get back online.
When Should You Use Network Reset?
Use Network reset when everything above has failed, because it removes and reinstalls every network adapter and returns networking components to default settings.
- Open Settings → Network & internet → Advanced network settings → Network reset.
- Select Reset now and confirm with Yes.
- Wait for the PC to restart, then reconnect the cable and test.
Afterwards you may need to reinstall VPN software or recreate Hyper-V virtual switches, and you may need to reconnect to saved Wi-Fi networks. Your network may also be set to public, so switch it back to private if you share files on your home network.
A Common Mistake We See
VPN clients and some security suites install their own virtual network adapters and filter drivers. When one of them breaks, Ethernet looks dead even though the cable, port and driver are fine. People reinstall Windows when uninstalling the VPN would have fixed it.
Before anything drastic, temporarily disconnect or uninstall any VPN and third-party firewall, then test. Check Settings → Network & internet → Proxy too, and make sure no manual proxy is set unless you need one.
Frequently Asked Questions
How do I fix ethernet not working on Windows 11?
Check the cable and port lights, restart the router, then make sure the adapter is enabled under Settings → Network & internet → Advanced network settings. Run the network troubleshooter, reset the network stack with netsh and ipconfig commands, and reinstall the Ethernet driver. Use Network reset only if nothing else works.
Why does my PC say Ethernet is connected but there's no internet?
Usually the PC hasn't received a valid IP address from the router, or DNS isn't resolving websites. Restart the router, then run ipconfig /release, ipconfig /renew and ipconfig /flushdns in an administrator Command Prompt. An address starting with 169.254 confirms the router didn't respond.
Why did my PC Ethernet stop working after an update?
A Windows update can replace the network driver with a different version that doesn't suit your adapter. Open Device Manager, right-click the Ethernet adapter, choose Properties → Driver → Roll Back Driver, or install the manufacturer's latest driver. If that doesn't help, uninstall the most recent update.
Can a bad Ethernet cable cause no connection?
Yes. A damaged cable, a broken clip or a bent pin in the port can stop the connection completely or make it drop in and out. The port's link light is a quick test: if it stays off with a known-good cable in a working router port, suspect the PC's port or adapter.
Does Network reset delete my files?
No. Network reset only removes and reinstalls network adapters and returns networking settings to their defaults. Your files and apps are untouched. You may need to reconnect to Wi-Fi networks, reinstall VPN software and set your home network back to private afterwards. Note any static IP or DNS settings before you start, because those are cleared too.
Conclusion
Most cases of ethernet not working on PC are fixed by checking the cable, renewing the IP address or reinstalling the driver, and only a few need Network reset or new hardware. If you are rebuilding a PC and need a fresh licence, our Windows 11 collection has Home and Pro keys that activate online.
Useful Links
| Resource | Link |
|---|---|
| Windows 11 licences | Windows 11 collection |
| Slow DNS fixes | How to fix slow DNS lookups |
| BIOS access | How to access BIOS in Windows 11 |
| Fast Startup | How to disable Fast Startup |
| Ethernet troubleshooting (Microsoft) | Fix Ethernet connection problems in Windows |
Deja un comentario